Catalog #: CMS-Emergency-Response-Kit-Drager-4055711
Our Price: $4,052.70
Quantity in Basket:
None
|
CMS Emergency Response Kit Includes; Analyzer Set, Remote System, Telescopic Probe, 10 Chips, and Carrying Case, By Dräger P/N 4055711
Chips Included in Kit; Amonia 10.0 - 150.0 ppm, Carbon Dioxide 1,000-25,000 ppm, Carbon Monoxide 5.0-150 ppm, Chlorine 0.20-10.0 ppm, Hydrochloric Acid 1.0-25.0 ppm, Hydrogen Sulfide 2.0-50 ppm, Nitrous Fumes 0.50-15.0 ppm, Perchloroethelene 5.0-150 ppm, Petroleum Hydrocarbons 20.0-500 ppm, and Sufer Dioxide 0.40-10.0 ppm.
CMS Analyzer By Dräger- The New Electronic Detector Tubes! - Accurate gas measurements are made easier with the Dräger CMS. This new generation spot-check detection device is literally as easy as 1-2-3 to operate. Simply insert one of the 55 chemical specific Dräger-CMS-Chips into the Analyzer and follow the instructions on the display as to when to move the slide switch. TWA levels are typically analyzed in 1-2 minutes. Upon completion of this process, the concentration is indicated on the LCD display. CMS: Chip
Measurement System-
The CMS combines substance specific
measuring Chips with an electronic
based Analyzer for an easy to use
spot-measurement system. The 10
capillaries in each Chip are filled with
a reagent system based on Draeger's
60+ years of colorimetric chemistry
expertise. The analyzer combines a
revolutionary optical system for analyzing
the color reaction with a mass flow
controller and pump system that
provides unbeatable reproducibility. Fast Response Times- The CMS Analyzer requires no warm-up
time. After taking a test, the results
can be reported as quickly as 20
seconds. Higher concentrations, which
pose a greater hazard, are reported
faster than trace background levels.
This increases the safety of using the
CMS system. TWA and action levels are
typically analyzed within 1-2 minutes.
After providing the measurement
results, the CMS is immediately ready
for another test or another Chip for
further analysis of the environment. Unequalled Accuracy The expertise of Draeger's worldwide
experience in industrial gas measurement
has come to focus in the CMS.
This is combined with a photo-optical
controller that measures the speed of
the chemical reaction, thus eliminating
the human objectivity. Unlike other
systems that rely on the volume of air,
the CMS pulls the same mass of air
through the capillary every time. The
mass flow controller automatically
compensates for changes in atmospheric
pressure.
Accuracies of +/- 4 to 7% of
measured value is achieved for
most gases.
CMS has been validated by a nationally
accredited third party laboratory.
Chemical Specific Chips
When you need to know exactly what is
there, CMS is the tool to provide those
answers. The chemistry is chosen to provide
the best results possible. The capillaries of
several chips have multiple levels (Yes, even
in something that small!) to help eliminate
cross sensitivity or derive a specific
measurement of the targeted chemical.
The CMS Chip The Chip consists of 10 measurement
capillaries filled with substance-specific
reagent systems. The gas type, part
number and batch number are printed on
the chip. A printed barcode on the chip,
read by the analyzer optics, contains
information about gas type, measuring
range and measuring time required for
completing the measurement. Each chip
is calibrated during manufacturing and is
valid for two years.
Simplified Operation
The CMS is literally as easy to
operate as 1-2-3. Making an
analysis is as simple as turning the
unit''on'' (moving the slide to position
1), then following the plain language
instructions on the display to load the
Chip and move the slide selector to
positions 2 and 3. Operating the
CMS couldn't be easier because
this is the exact same procedure
for every Chip! Upon completion of
the analysis, the CMS Analyzer shows
the concentration in the display. Any
misinterpretation of the results is
eliminated by the unambiguous digital
display of the concentration.
Simplified Maintenance
The CMS Analyzer does not
require gas calibration! All
calibration information is stored on
the bar code of the CMS Chip and
automatically downloaded to the
analyzer when inserted. An electronic
system self test is performed every
time the Analyzer is switched ON, and
a sampling system test is performed
before each test. You are always
assured that the CMS system is
operating properly. Operating on
alkaline batteries means that there
are no worries about charging or
battery memory. CMS is gas detection
made simple.
DataRecorder
The internal datarecorder stores up to
fifty measurements with the time/date,
contaminant/concentration and the
sequential number of the measurement
in a series. Measurement location information
(in alphabetical code) may be
entered manually. The stored data can
be recalled and displayed on demand.
Specifications
Size 8.0 x 3.6 x 1.7 in. (205 x 92 x 45 mm)
Weight 25.6 oz. (730 gr.)
Ingress Protection IP-54, protected against dust and water
Data Capacity Stores up to 50 measurements
Power Supply 4 x 1.5 Volt (AA) alkaline batteries
Battery Duration 450 minutes of analysis time (typically greater than 100 measurements)
Approvals UL: Class I, Division 1, Groups A-D, T4
CSA: Class I, Division 1, Groups A-D, T4
CENELEC: EEx ib IIC T4
MSHA (Permissible Gas Analyzer)
Operational Temp. 32-104°F (0-40°C)
Order Information
CMS Analyzer with Data Recorder 6405300
Remote System 6405060
Telescopic Probe (requires remote system) 8313025
Nylon Transport Case 4594631
Molded Plastic Transport Case 4056442
Leather Carrying Case with Shoulder Strap for Analyzer 6405080
Leather Carrying Case for Chips 6405090
The information contained within this publication is Copyright © 1976 - to present, either by the individual manufacturers, The Safety Equipment Store®, or both parties. The Safety Equipment Store®, and, Your One Source For Workplace Safety®, are Registered Service Marks of S&E Industrial Supply Co., Inc. 1976 - to present.
|
